Showing posts with label woodwork. Show all posts
Showing posts with label woodwork. Show all posts

Tuesday, February 2, 2021

Garden of freestyle delights - removable mini-shelf for a fence

 The Idea For the Mini-Shelf

It is always nice to have a proper spot to place a drink, or in these days, a cell phone.  The proper place is not the floor, especially on a patio or other outdoor place, and sometimes putting a drink on your own chair or lap can be ... dicey. The proper answer is stable shelf or side table, something that was lacking within arm's reach of one patio chair nestled into a corner.  So, given my quantity of scrapwood, I thought about how to make a shelf that would fit into the fence, but not require being fastened to the fence with nails or screws.

Pile of scrapwood, cambrige freestyle
Pile of scrapwood, aka inspiration material









The Prototype

The fence has alternating vertical pieces,  these vertical pieces are fastened to horizontal wood pieces running parallel to the ground.  One of the horizontal pieces is approximately 3 ft above the bottom of the fence, making it the perfect height for a mini shelf.  I came up with a T-shaped design for the shelf, with the bottom support provided by a small block of wood.

Mini-shelf, top-view. copyright M. Kress
Mini-shelf, top view.













In the picture ABOVE you can see how the narrow side arms of the 'T' shape had to be no thicker (when laid horizontally) than the space between the  vertical fence posts, which is roughly equal to the thickness of a 2x4.   The screw near the top is what held the small supporting block on the base. In the picture BELOW you can see the nail from the bottom of the shelf, on this prototype the small supporting block of wood split in half when I screwed through it - which is actually kind of helpful for showing the cross-section here.

Mini-shelf, bottom-view. copyright M. Kress
Mini-shelf, bottom-view.

The IMPORTANT part was that my idea worked! The shelf laid flat and stayed put by being braced between the vertical fence posts and was held level by the lower small block.

Mini-shelf, side-view. copyright M. Kress
Mini-shelf, side-view. 



Conclusion

After finalizing the measurements on the prototype mini-shelf I made another version of the shelf, with slightly neater cuts and maybe even some sanding to smooth the edges.  I then used a stencil to apply a purple floral mandala-type design.  After the paint was dry I coated the entire mini-shelf piece with polyurethane for protection from the elements.

Completed removable wooden mini-shelf, copyright M. Kress
Completed mini-shelf


You can see that this mini-shelf is the perfect size to hold a drink, a phone, or as one might expect in a patio space -- some gardening supplies.

Completed removable wooden mini-shelf holding scissors and twine, copyright M. Kress
Completed mini-shelf holding pruning scissors and twine.


















Happy freestyling, prototyping, and gardening!

Tuesday, July 21, 2020

Garden of freestyle delights - Scrap wood tomato planter

Garden of freestyle delights

When you see a pile of scrap wood...

Does your mind automatically start calculating how big of a rectangle-ish box you could make? 

Seeing how pieces could be cut up, fit together, drilled through, and screwed into to make yet another thing that can hold dirt?

Well my mind was VERY MUCH in that space this spring when I had the urge to setup a patio garden space and try my hand at growing cherry tomatoes again. It's probably been a decade, but there is never a bad time to return to vegetable gardening!

The wood

There was a pile of wood that was sitting abandoned for a while, which upon closer inspection turned out to be the remnants of a table. Some of the pieces had this lovely dappled silver pattern from the weathering.

Close-up image of weathered wood texture
Close-up of weathered wood













I have no idea if the wood was deliberately stained grey or if that was a reaction from being left outside. Either way, beautiful! 

Once we got all the pieces to the workspace the design of the planter started to come together a bit more, but first I had to take some pieces apart.  You can see the metal attachment plates for table legs in the picture below.

Pieces of scrap wood from abandoned table
Scrap wood from abandoned table



















Luckily I didn't have to try to pry these off with my bare hands, I had a few tools available at this point. The power drill was essential in deconstructing any unwanted parts and then building the planter with the L-brackets that I bought from the hardware store.


Supplies used to construct the scrap wood planter, saw, drill, brackets
Saw, drill, and L-brackets


















The planter

It is much easier to hold pieces in the proper alignment and screw them together with two people, so I'm glad I had a friend to help with this job.  There aren't any pictures of the sawing wood or actually screwing the pieces together with L-brackets, but here is what the basic box looked like when it was done.


Rectangular planter made from scrap wood
Rectangular planter made from scrap wood

In case you are wondering, there is a reason the back wood cross-piece is longer than the front. Aside from trying to minimize the amount of hand-sawing needed for this project I wanted extra space to attached a trellis at some future point since my plan was to grow cherry tomatoes.

Below is a closeup of the end, you can see the L-brackets are on the outside here, because the inner space was simply too small to fit the drill.  You can also see that the front wood had bowed a bit, which is ok because this is a planter.

Scrap wood planter, short end with visible brackets
Planter end with visible L-brackets


From this top view you can see the L-brackets that were used on the inside of the planter box so that they wouldn't show from the font.  You can also see the drainage holes I drilled in the bottom using the largest available drill bit. Always always always consider the drainage!

Scrap wood planter from above with drainage holes visible
Planter from above with drainage holes visible


Part of thinking about drainage is looking at where your planter will be sitting. If a planter has drainage holes but is sitting on another surface that traps water then the situation can encourage mold or algae growth.  Similarly, a planter sitting on a wooden surface can trap moisture on top of the wood deck lead to unwanted effects.  So just like drainage, it is also important to consider ventilation and air flow.  In this case I proper up the planter a few inches on some ceramic feet that I had found in a give-away pile.


Scrap wood planter sitting on clay feet for elevation
Scrap wood planter sitting on clay feet for elevation

There were only 3 ceramic feet so I had to space them carefully, but they held up to the weight just fine!  After getting the planter elevated and in the right position all that was left was to fill it with dirt and four tiny tomato seedlings.  For the cherry tomatoes I was limited to what was still available at the hardware store, and ultimately ended up with three 'supersweet 100 hybrid' strains and one 'black cherry tomato' strain.

Scrap wood planter with tomato seedlings
Scrap wood planter with tomato seedlings


You'll notice in the above picture that there are peppers and rosemary plants attached to the railing above the cherry tomatoes.  I knew while building the tomato planter box that this garden arrangement would have to shift, and eventually I'd need to add a trellis or some sort of support for the tomatoes because I wanted to do string training.  An excellent description of why and how to do string training for tomatoes is available on this website.  Stay tuned for trellis and string-training updates in another post.


Conclusions

Rome wasn't built in a day, your garden doesn't have to be either.  In creating this freestyle garden the goal was to spend as little money (preferably no money) on large heavy objects like planters that won't be making the next move (whenever that happens).  This means keeping an eye out for free scrap wood, free ceramics whether large, medium, or small, and especially free plastic planters (way easier to carry than large pieces of wood).  See the potential!

Happy freestyling!

Sunday, June 28, 2020

Garden of freestyle delights - Planter for cucumbers

Garden of freestyle delights 

How a scrap wood planter came to be.

The evolution of a patio from a nondescript outdoor space into a garden during this time of quarantine has been a welcome relief. Projects provide purpose. Gardening is known to be therapeutic, and for me, an extra layer of joy is added when the creation of a garden becomes a cross between a freestyle treasure hunt and impulse plant-buying.  In these 'Garden of freestyle delights' posts I'm going to describe different projects that have been part of this garden evolution.
If this space had all been planned - as a whole - from the beginning it would probably look much different and be worthier of Monty Don's approval. As it is, I hope he would appreciate the spirit, the creative reuse, and the adventure of how it has evolved so far. So let's get into it.

It started with finding some free pots set out on recycling night, like these.....


3 gallon black plastic plant pot
Sturdy black plastic pot
Maroon hanging ceramic pot, sitting upside-down
Maroon ceramic hanging pot, upside-down





















...and for a while it stayed quite modest.  
A few modest plants hanging out, waiting to see if they would get destroyed by insects, or birds, or the cat. 

























Just a few pots on the edge of the patio. 
Nothing special. 
Hardly even noticeable.....




















Then I got access to power tools and a whole new world of possibility opened up.
This meant that not only could I use freestyle planters (plastic, ceramic, etc) for gardening, but I could use freestyle scrap wood to MAKE MY OWN PLANTERS!!!!!  

Depending on where you live and the time of year there may or may not be lots of scrap wood out on the sidewalk. But let me tell you, in a warm-weather climate, during a time that coincided with spring cleaning AND a quarantine where people are at home AND beautiful weather for home renovations....
....yeah, there has been a lot of scrap wood out for free.

 If I had a truck to pick it up and a giant lawn I could make raised beds for days. But, as things stand I am mostly only taking what I can carry.  But I digress, let me return to the cucumber box.  I found a slightly rotting wooden table very close to the patio, and convinced a friend to help me move it. In my excitement I didn't take a 'before' picture. But it had two boards across the top, and two rectangles made of 2x4s for legs.


Construction

I realized that I could flip the setup of the existing table, use the table top as a base, and use the leg rectangles - stacked one on top of the other - as the sides for a planter.  I wouldn't even have to make any cuts with my glamorous hand saw.

Here is what the wooden pieces looked like after I removed the legs from the 'table top' pieces and laid them out to see what the planter would look like.  My plan was to secure the rectangles to each other, and secure the lower rectangle to the wooden base pieces using metal L-braces (purchased from a hardware store, using money).


I even saved the screws that I pulled out in case there was a way to reuse them. They were very rusty.


Remember how I mentioned that the table was 'slightly rotting'? Yeah, well, it has clearly been sitting outside for weeks (multiple months?), and there were mushrooms growing in the cracks. 
I took it as a good sign.


Here is the planter box after assembly and placement in the corner of the patio.  If this box were going to be moved often I would add a few more braces and brackets between the different parts, but the current plan is to use this for only one season.


You might notice that the planter box seems to be elevated off the deck. Good eye!  I didn't want the wooden base of the box to be sitting directly on the decking, so I stacked up some pieces of polystyrene to use as 'legs'.  I figured this setup would allow for airflow and better drainage. If polystyrene will last 10,000 years before degrading, then those legs should be able to handle the warm and rainy weather here!



The final step before adding the potting soil was to drill some more drainage holes in the base.  The two flat base pieces already had a slight gap between them from being warped and weathered, but I wanted more drainage. Drainage drainage drainage and no worries about rotting roots.


Since cucumbers are vining plants I wanted to add a trellis. Obviously I did not want to pay for a trellis.  In classic scavenged freestyle beauty fashion I found this pieces that appeared to be an old children's art easel out for the taking. I actually walked by it (along with various other discarded wood pieces) for a few nights before being able to pick it up using a friend's car (separate story there about looking for trellis supplies).  I took apart the V-shaped easel and used one half of it as a trellis base for these cucumber plants. The easel piece was just the right width to fit across the width of the planting box and to sit on top of the little shelf created by the long table-top-turned-planter-bottom pieces.  To give the cucumbers something to climb I added twine strings tied at the top, wrapped around each cross piece on their way down, and tied to another cross-piece of twine at the base. 


Conclusion

There you have it, a freestyle scavenged scrap wood planter box and trellis. The only costs for this project were the L-shaped brackets, the twine, the potting soil, and some small cucumber seedlings -- all from the hardware store.  Check back for other posts about creating a garden on the freap (free+cheap).

Happy freestyling and gardening.

"He that plants trees loves others besides himself."
--Thomas Fuller


Tuesday, October 15, 2019

Chair season - the angular colonial repro

DIY Furniture makeover of colonial-style chair with numerous spindles

Background

It is rare that I like the lines of a chair, especially upon first sight.
Such was the case with this wooden chair, which I believe to be a reproduction of something colonial, or maybe just colonial-inspired.


The bottom has a stamp that according to some internet research indicates that it was probably made in the middle part of the last century. The stamp says Fitchburg, Mass.

Refinishing the chair


For a while this chair served as a step stool around the house, and by 'a while' I mean about two years. It held up beautifully and was just the right height for so many tasks, from painting the ceiling and installing light fixtures to hanging art.  During that time it also got a little bit scuffed up, although the finish wasn't perfect to start with - free things rarely are.

Eventually, this winter, it might have been March, I decided to refinish the chair. I actually had to chairs to refinish, which apparently is a critical mass when you have limited storage space and want things to be functional and pretty.

Picture of chair that is going to be refinished and various refinishing supplies
Wooden chair holding the refinishing supplies.




















First I used citristrip.....

Chair laying on its side, after first round of finish remover was applied.
Wooden chair after the initial Citristrip application.
















...and that was a mistake because OH MY GOD ALL THOSE SPINDLES.
Small round spindles are not ideal for a product that you normally remove by scraping with a flat blade, because with each pass of the blade you only remove a tiny amount of the citristrip/old finish, rather than a 1-2inch section like you would on a flat surface.


Eventually I switched to sanding, but OH MY GOD ALL THOSE SPINDLES.  In the photo below you can see that the bottom half of the chair has been sanded (mostly by hand), but the top is still showing only the finish that was removed by citristrip.

Wooden chair after citristrip used on the top,  and sanding on the bottom part.
Wooden chair after citristrip used on the top,
and sanding on the bottom part.






















Wooden chair after switching to sanding as  the method to remove the old finish.
Wooden chair after switching to sanding as
the method to remove the old finish.























At one point I finished sanding and moved on to the step of (hopefully) fixing one of the cross brace pieces that had come loose. To stabilize this I used some wood glue and a belt to hold it like a clamp while it dried.

Wooden chair with loose cross brace being glued, secured with belts while the glue dries.
Wooden chair with loose cross brace being glued,
secured with belts while the glue dries.






















At this point I think I erred, because I decided to "branch out" and do something different by painting the chair instead of dyeing it with the pigments I had on hand.
Poor choice.
If I had dyed the wood and not liked it I could have eventually painted it, but one does not paint and then dye.  So, lesson learned, don't let haste and fear drive your design decisions.
Here it is, painted in Benjamin Moore Black Iron.

Wooden chair after being painted with the first coat of paint.
Wooden chair after being painted with the first coat of paint,
back side.




















Wooden chair refinished with black paint, first coat, front side.
Wooden chair after being painted with the first coat of paint,
front side
























To my eyes the first coat of paint looked grey, not black.

So I took the paint can back to my hardware store and had them add more pigment. Then I painted another coat.

Better, still not black, but again, the project fatigue was starting to set in. And of course I was peeved AT MYSELF for not dyeing the wood in the first place for fear of having an uneven finish like I had seen on my splat-back chair project.
Silly when I think about it in retrospect.

Conclusion, the finished-for-now chair


Here is how the chair stands (sits?) now.

Spindle-back chair refinished with black paint,  accessorized with decorative pillow.
Spindle-back chair refinished with black paint,
accessorized with decorative pillow.

Spindle-back chair refinished with black paint.
Spindle-back chair refinished with black paint.













































































And that is probably how it shall stay for a while, unless I decide to add a top coat.
Do I need a top coat?  How rough am I with my furniture? Polycrylic or shellac?
Or I could try to buy some of that alkyd paint I read about online that supposedly gives a tough enamel finish....  Paint costs can add up quickly and I really don't like a bunch of partially-used cans sitting around.  So many things for the freestylist to consider.

Happy freestyling!